This Adaptor is made from brass with a polished silver chrome finish.

It measures some 30mm across the widest section (base) and is some 27mm long. It has a 3/4" BSP female threaded section on the lower end (measuring 1" across in diameter inside), and a 1/2" BSP male threaded one on the top section (measuring 3/4" in diameter outside).

It is used to convert a 3/4" BSP male connection to a 1/2" BSP male one.

Round 'minimalist' style Combined Shower Head/Hose Holder with Wall Outlet Connection. This is for use with a 'concealed style shower valve.

The holder/outlet is solidly made from brass and chrome. The main body section measures some 7 cms long. The diameter of the body is 3 cms. The shower holder section on the side is 4 cms long.

It comes with a round 'plinth' which is some 5 cms diameter and 7mm deep.

The inside section is tapered so that the end of a shower hose fits securely. This section also pivots so you can adjust the angle of the shower head.

It also comes with securing nut and rubber washer and had a threaded 1/2" BSP Tail (3/4" diameter outside). The threaded tail is some 5 cms long.

The 'exposed' hose connection is a standard 1/2" BSP size also (3/4" diameter).

REPLACEMENT THERMOSTATIC CONTROL HANDLE FOR VARIOUS CONCEALED STYLE SHOWER VALVES & PANELS:

The Control handle comes with a 'stop ring', grub screw & end cap, and fits the 045, 046, 060, 075, 075B, 076, 077, 079, 158, 341, 344 Shower Valves/Panels.

Specification & Features:

Made from Brass with mjostly 'mirror' chrome finish, although there is a band of matt silver chrome around the inside rim. It measures some 50mm diameter and 40mm deep. The handle fitson thermostats with n24 splines/teeth and which measure 9.6mm diameter.

The stop ring is used to stop the handle turning beyond the normal 38 Degrees point unless the spring loaded button is depressed.

To install it with a Concealed shower valve, all you have to do is prise off the small cap opposite the spring loaded override button and undo the grub screw inside the handle until you can ease it off the splines on the thermostatic cartridge.

Wall-mounted Bath Filler Spout in Chrome to go with a concealed style Valve/Taps.

Solidly made from brass with a highly polished chrome finish.

Its body measures some 14.5 cms long (approx 13 cms to the centre of the spout). There is a securing nut and washer supplied also.

This Chrome Adaptor Bush converts shower connections from 1/2"BSP to 3/4"BSP.

It is made from brass with a chrome finish.

The inisde threaded section measures 3/4" diameter, and the outside threads measure 1" diameter. There is a 12mm hexagonal shape in the centre in order to secure it with a Hex/Allen key. The bush is approx 9mm deep in total.

It comes with a 1/2"BSP rubber washer.

This bush can be used in conjunction with the 194 Diverter, as well as the Torpedo style shower bar valves (058, 062, etc).

It is solidly made from brass and finished in polished 'mirror' Chrome and measures some 120mm in length (excluding the threaded tail section).

The body section is some 30mm in diameter. It's base sits in a 'plinth' measuring some 40mm diameter.

The threaded tail is 1/2" BSP (3/4" diameter outside) and is some 4 cms long.

There is a mesh filter contained within the tip and the end is angled at approx 20 degrees.

It comes with a securing nut and washer.

REPLACEMENT/REPAIR THERMOSTATIC CARTRIDGE FOR BATH MIXER & VARIOUS SHOWER VALVES/PANELS:

Symptoms: Does your tap/shower/valve no longer regulate the temperature effectively? Are you getting strange 'surging' or vibration noises? Are you is a hard water area like 60-65% of the UK?

Solution: Simply change the cartridge, not the whole tap or shower!

Specification & Features:

Principally made from brass, this generic Thermostatic Cartridge is suitable for many manufacturers, and most of the types of Taps and Shower Valves/Panels that we sell.

The operating Temperature range is between 20 to 48 Degrees C, with safety override button at the 38 Degrees C position. The cartridge comes calibrated to 38 Degrees C. There is no handle with this listing.

To install it with a Bath Mixer Tap or Torpedo style Bar Shower valves, all you have to do is remove the grub screw on the body underneath (3mm Allen key is commonly required), pull out the old cartridge, swap over the handle, push the new one into place, and re-secure the grub screw. With the concealed shower valves, the handle has to be removed and then the cartridge fitted separately. Lubrication may well be needed around the black rubber seals. Always ensure your water is off when fitting!!

It can also be used to replace some older style cartridges (see picture).

The Dimensions are: Total Length of Cartridge including the brass capsule is some 93.4mm. Widest section = 33mm diameter (round the thicker brass section where the grub screw hole is located). Base of cartridge to centre of Grub screw hole = 60mm. The 3 Black rubber washers are positioned at approx 7mm, 27mm and 47mm from the centre of the grub screw hole. There are 24 splines (teeth) and the diameter of these teeth on the spindle is 9.6mm.

Please check the images and the dimensions before purchasing and carefully compare to your one before installing. We also sell a variety of handles that fit this cartridge should you need one.

REPLACEMENT/REPAIR CERAMIC DISC WATER FLOW CARTRIDGE WITH CONTROL HANDLE FOR 057/057D BATH/SHOWER MIXER TAPS AND 058, 058/2, 058L SHOWER VALVES:

Symptoms: Does your Bath Tap or Shower Valve drip? Are you is a hard water area like 60-65% of the UK? Solution: Simply change the Ceramic Disc Cartridge, not the whole tap or shower! 
 

Principally made from brass, this Ceramic Disc Cartridge is suitable for various Mixer taps and shower valves.  Includes: Control handle, end cap cover, screw and Ceramic Disc Cartridge. The Handle and end cap are made from ABS 'Plastichrome' and the chrome is a 'mirror' finish one. This is the left side part as you look at the front of the Taps/Shower.

To install it with a Bath Mixer Tap or Torpedo style Bar Shower valves, all you have to do is prise off the end cap, remove the grub screw inside, then undo the 'nut' shaped section of the cartridge. Always ensure your water is off when fitting!!

The Dimensions are:  Total Length of Cartridge = 48mm. It is a standard 1/2"BSP size thread (measures 3/4" diameter where it fits into the taps/valve body). This 'inside' section that goes into the Taps/Shower is approx 22mm long.

Please check the image above and the dimensions before purchasing to ensure a good match and carefully compare to your one before installing. Please note this is NOT a Thermostatic valve.

REPLACEMENT THERMOSTATIC CONTROL HANDLE FOR 057U/057UD BATH SHOWER MIXER:

The Control handle comes with a 'stop ring', grub screw & end cap, and fits the 057U/057UD Bath Shower Mixer Taps.

Specification & Features:

Made from ABS plastic with 'mirror' chrome finish.

The stop ring is used to stop the handle turning beyond the 38 degrees point unless the spring loaded red button is depressed.

To install it with a Bath Mixer Tap or one of the Shower valves, to remove the old handle all you have to do is prise off the end cap section and undo the grub screw that holds the handle in place.

REPLACEMENT ON/OFF/FLOW CONTROL HANDLE FOR 057U/057UD BATH MIXER:

The Control handle comes with a grub screw & end cap, and fits the 057U/057UD Bath Shower Mixer.

Specification & Features:

Made from ABS plastic with 'mirror' chrome finish.

To install it with a Bath Mixer Tap or one of the Shower valves, to remove the old handle all you have to do is prise off the end cap and undo the grub screw inside the handle.