REPLACEMENT THERMOSTATIC CONTROL HANDLE FOR 057U/057UD BATH SHOWER MIXER:

The Control handle comes with a 'stop ring', grub screw & end cap, and fits the 057U/057UD Bath Shower Mixer Taps.

Specification & Features:

Made from ABS plastic with 'mirror' chrome finish.

The stop ring is used to stop the handle turning beyond the 38 degrees point unless the spring loaded red button is depressed.

To install it with a Bath Mixer Tap or one of the Shower valves, to remove the old handle all you have to do is prise off the end cap section and undo the grub screw that holds the handle in place.

REPLACEMENT ON/OFF/FLOW CONTROL HANDLE FOR 057U/057UD BATH MIXER:

The Control handle comes with a grub screw & end cap, and fits the 057U/057UD Bath Shower Mixer.

Specification & Features:

Made from ABS plastic with 'mirror' chrome finish.

To install it with a Bath Mixer Tap or one of the Shower valves, to remove the old handle all you have to do is prise off the end cap and undo the grub screw inside the handle.

REPLACEMENT/REPAIR CERAMIC DISC WATER FLOW CARTRIDGE WITH CONTROL HANDLE FOR 168/168D THERMOSTATIC BATH/SHOWER MIXER TAPS AND 162 SHOWER VALVE:

Symptoms: Does your Bath Tap or Shower Valve drip? Are you is a hard water area like 60-65% of the UK? Solution: Simply change the Ceramic Disc Cartridge, not the whole tap or shower! 
 

Principally made from brass, this Ceramic Disc Cartridge is suitable for various Mixer taps and shower valves.  Includes: Control handle, end cap cover, screw and Ceramic Disc Cartridge. The Handle and end cap are made from ABS 'Plastichrome' and the chrome is a 'mirror' finish one. This is the left side part as you look at the front of the Taps/Shower.

To install it with a Bath Mixer Tap or Torpedo style Bar Shower valves, all you have to do is prise off the end cap, remove the grub screw inside, then undo the 'nut' shaped section of the cartridge. Always ensure your water is off when fitting!!

The Dimensions are:  Total Length of Cartridge = 48mm. It is a standard 1/2"BSP size thread (measures 3/4" diameter where it fits into the taps/valve body). This 'inside' section that goes into the Taps/Shower is approx 22mm long.

Please check the image above and the dimensions before purchasing to ensure a good match and carefully compare to your one before installing. Please note this is NOT a Thermostatic valve.

REPLACEMENT/REPAIR CERAMIC DISC WATER FLOW CARTRIDGE WITH CONTROL HANDLE FOR 057U/057UD THERMOSTATIC BATH/SHOWER MIXER TAPS:

Symptoms: Does your Bath Tap or Shower Valve drip? Are you is a hard water area like 60-65% of the UK? Solution: Simply change the Ceramic Disc Cartridge, not the whole tap or shower! 
 

Principally made from brass, this Ceramic Disc Cartridge is suitable for various Mixer taps and shower valves.  Includes: Control handle, end cap cover, screw and Ceramic Disc Cartridge. The Handle and end cap are made from ABS 'Plastichrome' and the chrome is a 'mirror' finish one. This is the left side part as you look at the front of the Taps/Shower.

To install it with a Bath Mixer Tap or Torpedo style Bar Shower valves, all you have to do is prise off the end cap, remove the grub screw, then undo the 'nut' shaped section of the cartridge. Always ensure your water is off when fitting!!

The Dimensions are:  Total Length of Cartridge = 48mm. It is a standard 1/2"BSP size thread (measures 3/4" diameter where it fits into the taps/valve body). This 'inside' section that goes into the Taps/Shower is approx 22mm long.

Please check the image above and the dimensions before purchasing to ensure a good match and carefully compare to your one before installing. Please note this is NOT a Thermostatic valve.

SET OF 2 OFFSET THREADED 'S' TAIL CONNECTORS, 2 CHROME COVER PLATES AND 2 RUBBER/MESH FILTER WASHERS (3/4" BSP) FOR WALL MOUNTED TAPS AND SHOWERS.
 

• THESE ARE ALL NEW ITEMS.
• THE CHROME COVER PLATES ARE MADE FROM THIN BRASS WITH A MIRROR CHROME FINISH. THEY MEASURE SOME APPROX 65MM ACROSS IN OVERALL DIAMETER, THE CENTRAL HOLE IS 3/4"BSP (MEASURES 1" DIAMETER), AND THEY ARE APPROX 20MM DEEP. 
• THE WASHERS ARE 3/4"BSP (MEASURE 1") AND HAVE A METAL MESH CENTRE. THIS CAN BE REMOVED IF NOT NECESSARY. THEY ARE APPROX 3MM THICK.
• THE CRANKED OFFSET THREADED 'S' TAILS ARE MADE FROM BRASS AND ARE 3/4"BSP ON ONE END AND 1/2"BSP ON THE OTHER. THE OVERALL LENGTH IS APPROX 45MM. THE THREADED 'MALE' END SECTIONS ARE APPROX 15MM EACH.
• THESE KITS CAN BE USED WITH BOTH WALL MOUNTED TAPS & 'EXPOSED' SHOWERS IN ORDER TO CONECT UP TO WALL-MOUNTED PIPEWORK.

Please note that the threaded brass tails may be chromed so are silver in colour. This doesn't affect them in any adverse way!

REPLACEMENT THERMOSTATIC CONTROL HANDLE FOR VARIOUS CONCEALED STYLE SHOWER VALVES & PANELS:

The Control handle comes with a 'stop ring', grub screw & end cap, and fits the 045, 046, 060, 075, 075B, 076, 077, 079, 158, 341, 344 Shower Valves/Panels.

Specification & Features:

Made from Brass with mjostly 'mirror' chrome finish, although there is a band of matt silver chrome around the inside rim. It measures some 50mm diameter and 40mm deep. The handle fitson thermostats with n24 splines/teeth and which measure 9.6mm diameter.

The stop ring is used to stop the handle turning beyond the normal 38 Degrees point unless the spring loaded button is depressed.

To install it with a Concealed shower valve, all you have to do is prise off the small cap opposite the spring loaded override button and undo the grub screw inside the handle until you can ease it off the splines on the thermostatic cartridge.

REPLACEMENT ON OFF FLOW CONTROL HANDLE FOR VARIOUS CONCEALED STYLE SHOWER VALVES & PANELS:

The Control handle comes with a side Button & securing grub screw, and fits the 045, 046, 060, 075, 075B, 076, 077, 079, 158, 341, 344 Shower Valves/Panels.

Specification & Features:

Made from Zinc with a 'mirror' chrome finish, the handle measures some 48mm diameter and 29mm deep. They fit onto Ceramic Disc cartridges with 20 splines (teeth) measuring 7.5mm diameter.

To install it with a Concealed shower valve or panel, all you have to do is unscrew the side button and undo the grub screw inside the handle until you can ease it off the splines on the ceramic disc cartridge.

CERAMIC DISC CARTRIDGE 40MM:

New Water Control 'On/Off' Cartridge for either Kitchen or Bathroom Taps, or Manual Mixer Shower Valves.

The 25mm is the Diameter of the Cartridge main body. The overall length (excluding the lugs) is some 49.5mm. The off-white coloured top section is some 17 x 9 x 9mm. Other  measurements are shown in the pictures.

There are 3 holes on the base with rubber seals which need to be tightly secured in the tap cavity. It has 2 securing 'lugs' on the base and the distance between the centres of these is 16.5mm.

The Minimum recommended water pressure is 0.5 bars.

If your taps are leaking or won't shut off, then you may just need one of these Replacement Cartridges, instead of having to replace the whole tap!

This Chrome Adaptor Bush converts shower connections from 1/2"BSP to 3/4"BSP.

It is made from brass with a chrome finish.

The inisde threaded section measures 3/4" diameter, and the outside threads measure 1" diameter. There is a 12mm hexagonal shape in the centre in order to secure it with a Hex/Allen key. The bush is approx 9mm deep in total.

It comes with a 1/2"BSP rubber washer.

This bush can be used in conjunction with the 194 Diverter, as well as the Torpedo style shower bar valves (058, 062, etc).

CHROME BACKPLATE ELBOW FOR SHOWER ARM Specification & Features:

This is a Back Plate Elbow for a 'fixed' wall-mounted Shower Arm. It is solidly made from brass with a chrome finish.

It can either be installed inside a wall cavity and be used with a 'concealed' style shower valve & wall-mounted arm, or it can be fixed directly to a shower wall and connected to an 'exposed' shower.

The Arm connection is 'female' 1/2" BSP and there is an 'Olive' joint on the other end (1/2" BSP/15mm). It can be used with either a Rigid Riser Rail, Copper Pipework, or a Flexi hose.

The 'Plate' has been rounded and then 'squared off' across the lower part. It has 3 fixing holes and measures some 5 cms across in diameter, by 3.8cms high. Fittings are not supplied.