Deck Mounting Pair of 'legs' or 'Pillars' for mounting a mixer to a bath.

They are solidly made from Brass with a 'Mirror' chrome finish.

These are required for converting Wall-mounted Taps to Deck Mounted ones.

They stand some 9 cms high (excluding the threaded section) and are approx 5 cms in diameter at their widest. These Angles do splay out, so once attached to bath taps which have a 15cms gap between the inlet centres, the gap increases to around 18cms.

Standard UK sized 3/4" BSP threaded connections at the base. They also come with securing nuts and washers. NB: The washers could be either white or black rubber ones.

The length of the body of the waste is some 75mm. The diameter of the body and threaded section at the bottom is 40mm so it fits a UK standard 'P' trap, etc. The top 'Plug' section measures 62mm across in diameter.

The centre section pushes in by hand and springs up to open. It then pushes in again to close.

The waste is solidly made from brass with a chrome finish. It comes with securing nut and rubber seals.

EASY FIT CHROME WALL MOUNTED FIXING KIT FOR EXPOSED SHOWER VALVE & BATH TAPS:

Specification & Features:

This is a pair of Wall mounting kits for a set of Bath taps or 'Exposed' Shower Valve, or similar. It is made from brass with a polished 'mirror' chrome finish on the front cover plates. The Plates are also made from brass (not plastic like the Bristan ones are!).

Each Plate is some 67mm diameter wide and some 17mm deep.

The kits come with two Plates, two threaded sections with 'olives' and two brass securing plate for the wall. The threaded sections are 3/4"BSP(measuring 1" diameter outside) which is the UK standard for this sort of shower/taps.

The kits can be fitted to suit showers/taps with inlet centres as required, not just 150mm ones.

2 screws & raw plugs are also supplied, although the type of wall will determine whether these can be used.

REPLACEMENT/REPAIR THERMOSTATIC CARTRIDGE FOR BATH MIXER & VARIOUS SHOWER VALVES:

Symptoms: Does your tap/shower/valve no longer regulate the temperature effectively? Are you getting strange 'surging' or vibration noises? Are you is a hard water area like 60-65% of the UK?

Solution: Simply change the cartridge, not the whole tap or shower!

Specification & Features:

Principally made from brass, this generic Thermostatic Cartridge is suitable for many manufacturers, and some of the types of Taps and Showers that we sell are shown in the Picture gallery above.

The operating Temperature range is between 20 to 48 Degrees C, with safety override button at the 38 Degrees C position. The cartridge comes calibrated to 38 Degrees C with the handle and safety 'stop ring' already attached.

To install it with a Bath Mixer Tap or Torpedo style Bar Shower valves, all you have to do is remove the grub screw on the body underneath (3mm Allen key is commonly required) and push it into place. With the concealed shower valves, the handle has to be removed and then the cartridge fitted separately. Lubrication may well be needed around the black rubber seals. Always ensure your water is off when fitting!!

It can also be used to replace some older style cartridges (see picture).

The Dimensions are: Total Length of Cartridge = 95mm. Widest section = 33mm diameter (round the thicker brass section where the grub screw hole is located). Base of cartridge to centre of Grub screw hole = 60mm. The 3 Black rubber washers are positioned at approx 7mm, 27mm and 47mm from the centre of the grub screw hole.

Please check the images and the dimensions before purchasing and carefully compare to your one before installing.

REPLACEMENT/REPAIR THERMOSTATIC CARTRIDGE FOR BATH MIXER & VARIOUS SHOWER VALVES:

Symptoms: Does your tap/shower/valve no longer regulate the temperature effectively? Are you getting strange 'surging' or vibration noises? Are you is a hard water area like 60-65% of the UK?

Solution: Simply change the cartridge, not the whole tap or shower!

Specification & Features:

Principally made from brass, this generic Thermostatic Cartridge is suitable for many manufacturers, and some of the types of Taps and Showers that we sell are shown in the Picture gallery above.

The operating Temperature range is between 20 to 48 Degrees C, with safety override button at the 38 Degrees C position. The cartridge comes calibrated to 38 Degrees C with the handle and safety 'stop ring' already attached.

To install it with a Bath Mixer Tap or Torpedo style Bar Shower valves, all you have to do is remove the grub screw on the body underneath (3mm Allen key is commonly required) and push it into place. With the concealed shower valves, the handle has to be removed and then the cartridge fitted separately. Lubrication may well be needed around the black rubber seals. Always ensure your water is off when fitting!!

It can also be used to replace some older style cartridges (see picture).

The Dimensions are: Total Length of Cartridge = 95mm. Widest section = 33mm diameter (round the thicker brass section where the grub screw hole is located). Base of cartridge to centre of Grub screw hole = 60mm. The 3 Black rubber washers are positioned at approx 7mm, 27mm and 47mm from the centre of the grub screw hole.

Please check the images and the dimensions before purchasing and carefully compare to your one before installing.

REPLACEMENT THERMOSTATIC CONTROL HANDLE FOR 057 BATH MIXER & VARIOUS SHOWER VALVES:

The Control handle comes with a 'stop ring', grub screw & end cap, and fits the 057 Bath Shower Mixer and various shower valves (058, 034, & 063).

Specification & Features:

Made from ABS plastic with 'mirror' chrome finish.

The stop ring is used to stop the handle turning beyond the 38 degrees point unless the spring loaded red button is depressed.

To install it with a Bath Mixer Tap or one of the Shower valves, to remove the old handle all you have to do is prise off the end cap and undo the grub screw inside the handle.

REPLACEMENT ON/OFF/FLOW CONTROL HANDLE FOR 057 BATH MIXER & VARIOUS SHOWER VALVES:

The Control handle comes with a grub screw & end cap, and fits the 057 Bath Shower Mixer and various shower valves (058, 034, & 063).

Specification & Features:

Made from ABS plastic with 'mirror' chrome finish.

Fits onto Ceramic Disc Cartridges with 20 Splines (Teeth) that measure some 7.5mm diameter. 

To install it with a Bath Mixer Tap or one of the Shower valves, to remove the old handle all you have to do is prise off the end cap and undo the grub screw inside the handle.

REPLACEMENT/REPAIR THERMOSTATIC CARTRIDGE FOR BATH MIXER & VARIOUS SHOWER VALVES/PANELS:

Symptoms: Does your tap/shower/valve no longer regulate the temperature effectively? Are you getting strange 'surging' or vibration noises? Are you is a hard water area like 60-65% of the UK?

Solution: Simply change the cartridge, not the whole tap or shower!

Specification & Features:

Principally made from brass, this generic Thermostatic Cartridge is suitable for many manufacturers, and most of the types of Taps and Shower Valves/Panels that we sell.

The operating Temperature range is between 20 to 48 Degrees C, with safety override button at the 38 Degrees C position. The cartridge comes calibrated to 38 Degrees C. There is no handle with this listing.

To install it with a Bath Mixer Tap or Torpedo style Bar Shower valves, all you have to do is remove the grub screw on the body underneath (3mm Allen key is commonly required), pull out the old cartridge, swap over the handle, push the new one into place, and re-secure the grub screw. With the concealed shower valves, the handle has to be removed and then the cartridge fitted separately. Lubrication may well be needed around the black rubber seals. Always ensure your water is off when fitting!!

It can also be used to replace some older style cartridges (see picture).

The Dimensions are: Total Length of Cartridge including the brass capsule is some 93.4mm. Widest section = 33mm diameter (round the thicker brass section where the grub screw hole is located). Base of cartridge to centre of Grub screw hole = 60mm. The 3 Black rubber washers are positioned at approx 7mm, 27mm and 47mm from the centre of the grub screw hole. There are 24 splines (teeth) and the diameter of these teeth on the spindle is 9.6mm.

Please check the images and the dimensions before purchasing and carefully compare to your one before installing. We also sell a variety of handles that fit this cartridge should you need one.

REPLACEMENT/REPAIR CERAMIC DISC WATER FLOW CARTRIDGE WITH CONTROL HANDLE FOR 057/057D BATH/SHOWER MIXER TAPS AND 058, 058/2, 058L SHOWER VALVES:

Symptoms: Does your Bath Tap or Shower Valve drip? Are you is a hard water area like 60-65% of the UK? Solution: Simply change the Ceramic Disc Cartridge, not the whole tap or shower! 
 

Principally made from brass, this Ceramic Disc Cartridge is suitable for various Mixer taps and shower valves.  Includes: Control handle, end cap cover, screw and Ceramic Disc Cartridge. The Handle and end cap are made from ABS 'Plastichrome' and the chrome is a 'mirror' finish one. This is the left side part as you look at the front of the Taps/Shower.

To install it with a Bath Mixer Tap or Torpedo style Bar Shower valves, all you have to do is prise off the end cap, remove the grub screw inside, then undo the 'nut' shaped section of the cartridge. Always ensure your water is off when fitting!!

The Dimensions are:  Total Length of Cartridge = 48mm. It is a standard 1/2"BSP size thread (measures 3/4" diameter where it fits into the taps/valve body). This 'inside' section that goes into the Taps/Shower is approx 22mm long.

Please check the image above and the dimensions before purchasing to ensure a good match and carefully compare to your one before installing. Please note this is NOT a Thermostatic valve.

Victorian Style handheld Shower Head in Chrome finish with a White Handle. The main body is principally made from brass.

It has a Standard 1/2" BSP threaded connection and measures approx 17 cms long, with the head itself having a diameter of some 50mm wide. The threaded connection is a standard 1/2"BSP (measuring 3/4" diameter).

The Handle of the shower head is made from White ABS plastic.